Search...
NY8A051H is an EPROM based 8-bit MCU tailored for I/O based applications like remote controllers, fan/light controller, game controllers, toy and various controllers. NY8A051H adopts advanced CMOS technology to provide customers remarkable solution with low cost and high performance benefits. RISC architecture is applied to NY8A051H and it provides 55 instructions. All instructions are executed in single instruction cycle except programbranch and skip instructions which will take two instruction cycles. Therefore, NY8A051H is very suitable for those applications that are sophisticated but compact program size is required.
As NY8A051H address I/O type applications, it can provide 6 I/O pins for applications which require abundant input and output functionality. Moreover, each I/O pin may have additional features, like Pull-High/Pull-Low resistor and open-drain output type through programming. Moreover, NY8A051H has built-in infrared (IR) carrier generator with selectable IR carrier frequency and polarity for applications which demand remote control feature.
NY8A051H employs dual-clock oscillation mechanism, both high oscillation or low oscillation can be derived from internal resistor/capacitor oscillator. Moreover, based on dual-clock mechanism, NY8A051H provides kinds of operation mode like Normal mode, Slow mode, Standby mode and Halt mode in order to save power consumption and lengthen battery operation life.
While NY8A051H operates in Standby mode and Halt mode, kinds of event will issue interrupt requests and can wake-up NY8A051H to enter Normal mode and Slow mode in order to process urgent events.
Wide operating voltage range:2.0V ~ 5.5V @system clock ≦8MHz.2.2V ~ 5.5V @system clock ＞8MHz.
Wide operating temperature: -25°C ~ 85°C.
High ESD over ±5KV.
Built-in high-precision Low-Voltage Detector (LVD).
1K x 14 bits EPROM.
48 bytes SRAM.
6 general purpose I/O pins (GPIO), PB[5:0], with independent direction control.
PB[3:0] has features of Pull-High and Pull-Low resistor for input pin.
PB[5:0] has features of Pull-High resistor, and open-drain output.
ViH / ViL has three types to choose (TTL/CMOS/ Without Schmitt).
PB[3] built-in Pull-High resistor and add output high function.
8-level hardware Stack.
Direct and indirect addressing modes for data access.
One 8-bit up-count timer (Timer0) with programmable pre-scalar.
One 8-bit reload or continuous down-count timers (Timer1).
One 8-bit resolution PWM (PWM1) output.
One buzzer (BZ1) output.
Selectable 38/57KHz IR carrier frequency and high/low polarity according to data value.
Built-in Power-On Reset (POR).
Built-in Low-Voltage Reset (LVR).
Built-in Watch-Dog Timer (WDT) enabled/disabled by firmware control.
Dual-clock oscillation: System clock can switch between high oscillation and low oscillation.High oscillation: I_HRC (Internal High Resistor/Capacitor Oscillator ranging from 1M~20MHz);Low oscillation: I_LRC (Internal 32KHz oscillator).
Four kinds of operation mode to reduce system power consumption:Normal mode, Slow mode, Standby mode and Halt mode.
Six hardware interrupt events:Timer0 overflow interrupt.Timer1 underflow interrupt.WDT timeout interrupt.PB input change interrupt.External interrupt.LVD interrupt.
Six interrupt events to wake-up NY8A051H from Standby mode:Timer0 overflow interrupt.Timer1 underflow interrupt.WDT timeout interrupt.PB input change interrupt.External interrupt.LVD interrupt.
Three interrupt events to wake-up NY8A051H from Halt mode:WDT timeout interrupt.PB input change interrupt.External interrupt.
You can get your Nyquest MCU NY8A051H solution by flling out the form below and we will contact you immediately.
Nyquest MCUs Puya MCUs YF Co-packaged MCUs Holtek MCUs JL Bluetooth Chips Customized PCBA Design
Company Profile Certificates Terms & Conditions Privacy Statement
MCU Solutions
PCBA Solutions
Bluetooth Solutions
FAQ
Contact Us
Company News
Bluetooth Chip News
MCU News
PCBA News
Company Profile
Certificates
Terms & Conditions
Privacy Statement
