Search...
NY8B060D is an EPROM based 8-bit MCU tailored for ADC based applications like home appliances or meter equipment. NY8B060D adopts advanced CMOS technology to provide customers remarkable solution with low cost, high performance. RISC architecture is applied to NY8B060D and it provides 55 instructions. All instructions are executed in single instruction cycle except program branch and skip instructions which will take two instruction cycles. Therefore, NY8B060D is very suitable for those applications that are sophisticated but compact program size is required.
NY8B060D provides 5+2 channel high-precision 12-bit analog-to-digital converter (ADC), and high-precision Low Dropout Regulator and analog voltage comparator. They are suitable for any analog interface detection and measurement applications.
As NY8B060D address I/O type applications, it can provide 6 I/O pins for applications which require abundant input and output functionality. Moreover, each I/O pin may have additional features, like Pull-High/Pull-Low resistor and open-drain output type through programming. Moreover, NY8B060D has built-in infrared (IR) carrier generator with selectable IR carrier frequency and polarity for applications which demand remote control feature.
NY8B060D also provides 2 sets of timers which can be used as regular timer based on system oscillation or event counter with external trigger clock. Moreover, NY8B060D provides 3 sets of 10-bit resolution Pulse Width Modulation (PWM) output and 1 sets of buzzer output in order to drive motor/LED and buzzer.
NY8B060D employs dual-clock oscillation mechanism, either high oscillation or low oscillation can be derived from internal resistor/capacitor oscillator. Moreover, based on dual-clock mechanism, NY8B060D provides kinds of operation mode like Normal mode, Slow mode, Standby mode and Halt mode in order to save power consumption and lengthen battery operation life. While NY8B060D operates in Standby mode and Halt mode, kinds of event will issue interrupt requests and can wake-up NY8B060D to enter Normal mode and Slow mode in order to process urgent events.
Wide operating voltage range:
2.0V ~ 5.5V @system clock ≦8MHz.
2.2V ~ 5.5V @system clock > 8MHz.
Wide operating temperature: -40°C ~ 85°C.
1K x 14 bits EPROM.
64 bytes SRAM.
6 general purpose I/O pins (GPIO), PA[5,4,2], PB[3,2,1], with independent direction control.
PA[5,4,2] and PB[3,2,1] have features of Pull-Low resistor for input pin.
PA[5,4,2] and PB[3,2,1] have features of Pull-High resistor.
PB[3,2,1] have features of Open-Drain output.
PA[5] have feature of input or open-drain output.
I/O ports output current mode can be normal sink or large sink.
8-level hardware Stack.
Direct and indirect addressing modes for data access.
One 8-bit up-count timer (Timer0) with programmable prescaler.
One 10-bit reload or continuous down-count timers (Timer1).
Three 10-bit resolution PWM (PWM1, 2, 3) output.
One buzzer (BZ1) output.
Selectable 38/57KHz IR carrier frequency and high/low polarity according to data value.
Built-in high-precision Low-Voltage Detector (LVD).
Built-in 6+1 channel high-precision 12-bit ADC.
Built-in high-precision Voltage Comparator.
Built-in Power-On Reset (POR).
Built-in Low-Voltage Reset (LVR).
Built-in Watch-Dog Timer (WDT) enabled/disabled by firmware control.
Built-in Resistance to Frequency Converter (RFC) function.
Dual-clock oscillation: System clock can switch between high oscillation and low oscillation.
High oscillation: I_HRC (Internal High Resistor/Capacitor Oscillator ranging from 1M~20MHz)
Low oscillation: I_LRC (Internal 32KHz oscillator)
Four kinds of operation mode to reduce system power consumption:
Normal mode, Slow mode, Standby mode and Halt mode.
Seven hardware interrupt events:
Timer0 overflow interrupt.
Timer1 underflow interrupt.
WDT timeout interrupt.
PA/PB input change interrupt.
1 set External interrupt.
LVD interrupt.
ADC end-of-convert interrupt.
Seven interrupt events to wake-up NY8B060D from Standby mode:
Timer0 overflow interrupt.
Timer1 underflow interrupt.
WDT timeout interrupt.
PA/PB input change interrupt.
1 set External interrupt.
LVD interrupt.
ADC end-of-convert interrupt.
Three interrupt events to wake-up NY8B060D from Halt mode:
WDT timeout interrupt.
PA/PB input change interrupt.
1 set External interrupt.
You can get your Nyquest MCU NY8B060D solution by flling out the form below and we will contact you immediately.
Nyquest MCUs Puya MCUs YF Co-packaged MCUs Holtek MCUs JL Bluetooth Chips Customized PCBA Design
Company Profile Certificates Terms & Conditions Privacy Statement
MCU Solutions
PCBA Solutions
Bluetooth Solutions
FAQ
Contact Us
Company News
Bluetooth Chip News
MCU News
PCBA News
Company Profile
Certificates
Terms & Conditions
Privacy Statement
